Verint Nextiva S1700e Series Podręcznik Użytkownika Strona 39
- Strona / 111
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Verint Video Solutions 23
Nextiva S1100w User Guide
To install an external antenna:
1. Install the antenna above the S1100w device. If you bought your antenna from Verint
Video Solutions, use the supplied pole mount bracket.
2. Screw the SMA connector of the antenna cable to the S1100w antenna port and tighten
it with a 0.25-inch (0.6 centimeter) wrench.
Warning: Do not over-tighten to avoid damaging the connector. The recommended
torque is 8 lb.-in. (100 N-cm). You could use a calibrated SMA torque wrench
(for instance, from the Pasternack company, available at
www.pasternack.com).
3. Apply two or three layers of electrical tape around all RF connections.
The antenna cable and connectors are weather-tight; however, vibration caused by the
wind will over time loosen the connectors and reduce the efficiency of the gaskets. The
electrical tape will prevent this situation.
4. Carefully align the antennas of the S1100w and outdoor wireless bridge so that they
have a clear RF line of sight.
5. To improve the signal level between both devices, use the antenna alignment utility
from SConfigurator.
Performing the RS-422/485 Serial Connection
The Nextiva edge devices support only the RS-232, RS-422, and RS-485 asynchronous
protocols. For any other protocol, you may need a converter.
Warning: At any time there must be only one serial peripheral connected to the edge
device. For instance, when configuring the device through a COM port of the
computer, you must unplug any RS-422/485 peripheral.
RS-422/485
You use the CAB9P cable to properly connect the device to an RS-422 or RS-485 peripheral.
Here is the wiring scheme for the four-wire RS-422 or RS-485 protocol:
Cable Peripheral
Signal name Wire pair Wire color Signal name
Rx+ green/black green Rx+
Rx- black Rx-
Tx+ yellow/black yellow Tx+
Tx- black Tx-
Signal ground brown/black brown Signal ground
Signal ground black Signal ground
- Nextiva S1100w 1
- User Guide 3
- Verint Video Solutions iii 5
- Contents 7
- Verint Video Solutions vii 9
- Verint Video Solutions ix 11
- Who Should Read this Guide 12
- How to Use this Guide 12
- Related Nextiva Products 13
- About Us 13
- Warranty 14
- Verint Video Solutions xiii 15
- Overview 17
- About the S1100w 18
- Shipment 19
- Casing Description 20
- System and RF Planning 21
- Frequency Bands and Channels 22
- Wireless Cells 23
- System Planning 23
- Compatibility Issues 24
- S3100 3 S3100 2 25
- S1100w 2 25
- S1100w 1 25
- Colocated Cells 26
- Distance Limitations 27
- 5 GHz Band in Europe 28
- S3100 S3100 29
- RF Planning 30
- Antenna Requirements 31
- Interference 32
- RF Exposure Considerations 32
- Configuring and 33
- Installing the Device 33
- Serial Port 34
- Computer Requirements 35
- Setting Parameters 35
- Point-to-Point Connection 36
- Verint Video Solutions 21 37
- Installing the Transmitter 38
- Installing an Antenna 38
- RS-422/485 39
- Configuring the I/Os 41
- Updating the Firmware 43
- Performing a Hardware Reset 43
- Red/Blue Display 44
- Quality of Service 44
- Status LED 44
- Verint Video Solutions 29 45
- 30 Verint Video Solutions 46
- Setting Parameters with 47
- Getting Started 48
- Access Management 50
- User Accounts 51
- Security 51
- Network 52
- Wireless Communication 53
- Advanced Parameters 54
- Key Entry Format 55
- Tx Power Scale 55
- Sensitivity Threshold 55
- Minimum Margin 55
- Indoor/Outdoor RF Regulation 55
- System Status 56
- Advanced 56
- Load Default Configuration 57
- Reboot System 57
- 42 Verint Video Solutions 58
- Factory Default 59
- Configuration 59
- Cable Connections 61
- B: Cable Connections 62
- 46 Verint Video Solutions 62
- Here is its pinout: 64
- DHCP Support and 65
- C: DHCP Support and APIPA 66
- 50 Verint Video Solutions 66
- DTE and DCE 67
- Connections 67
- Verint Video Solutions 53 69
- 54 Verint Video Solutions 70
- CLI with Telnet 71
- E: CLI with Telnet 72
- 56 Verint Video Solutions 72
- Verint Video Solutions 57 73
- 58 Verint Video Solutions 74
- Surge Protection 75
- F: Surge Protection 76
- 60 Verint Video Solutions 76
- Channels 77
- Separation Between 77
- Devices Using Adjacent 77
- Verint Video Solutions 63 79
- 64 Verint Video Solutions 80
- 13 feet (4m): 81
- 13 feet (4m) 81
- 3.3 feet (1m) each 81
- 66 Verint Video Solutions 82
- Motion Track 83
- Motion Detection Processing 84
- Physical Connections 84
- Establishing a Connection 85
- H: Motion Track 86
- 70 Verint Video Solutions 86
- Configuring the DVMD Module 87
- Status Information 88
- Files Settings 89
- Display Settings 90
- Verint Video Solutions 75 91
- Sensitivity Settings 92
- Target Settings 93
- Target Size 94
- Technical Specifications 95
- 82 Verint Video Solutions 98
- Verint Video Solutions 83 99
- Glossary 100
- 84 Verint Video Solutions 100
- Verint Video Solutions 85 101
- Nextiva S1100w User Guide 101
- 86 Verint Video Solutions 102
- Numerics 103
- Compliance 107
- 92 Verint Video Solutions 108
- Declaration of Conformity 109
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Verint Nextiva S1700e Series
(74 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji